7 Steps to Solve Pachislo Slot Machine Hopper Issues

[ad_1]

Easy Solutions for Pachislo Hopper Errors

Most hopper issues are easy to solve. Hopper error codes are general as well as do not give you specific details as to the issue itself. First you need to find the problem.

Step 1: Remove the Hopper

There are types of hopper connections – one that has a cord that goes from the hopper to the powerfulness render, as well as the other where the hopper is automatically connected when it is inserted completely into the back of the machine.

If your hopper has a wire going from the hopper to the powerfulness render, that wire can be removed from the powerfulness render or, depending upon the hopper, from a connector on the hopper itself.

Pull the hopper towards you – it is held on by a track as well as may be tight, just wiggle it slightly left to right while pulling it. Some have a white clip on the forepart bottom that you testament need to push down while pulling the hopper towards you. Others may have a piece of plastic in forepart of the hopper on the machine. Just lift the hopper over the plastic while pulling it towards you.

If your hopper is connected by a wire, remove the wire from either the hopper itself or the powerfulness render.

Step 2: Remove the Top of the Hopper

Hoppers have two sections that are either screwed or clipped together. The top section is the plastic that the coins fall into. The bottom section is the wheel, plug/connector as well as sensor. The top part of the hopper can be removed.

If your hopper has screws just remove the screws with a Phillips screwdriver. There should be four screws – two located on the inside of the hopper as well as two on the outside of the coin area. When the two screws are removed the top testament come off as well as you testament be holding the entire bottom area with the wheel exposed.

There are also hopper that have clips holding the top to the bottom. These clips are usually yellow. The most common has two yellow clips on the forepart corners. Pull the clips toward you.

Step 3: Look for Jammed Coins

Look at the area where the coins exit the hopper as well as in the holes in the wheel itself for jammed coins. You testament see them immediately now that you can view the entire wheel area. Remove the obstruction as well as test the wheel manually.

Step 4: Lubricate the Wheel

You should be able to turn the hopper wheel clockwise with little resistance. If you have no coins jammed in the machine, try to spin the wheel. If it seems tight, has rust, etc. check again for obstructions. Clean the wheel, the area around it, etc. You may need to give it a quick spray of silicone – do not use WD40 as well as do not use a lot of spray. A quick spray testament do it. Work the wheel for a few minutes to let the lubricant do its work.

Step 5: Clean the Sensor

If the wheel is moving freely as well as you see no obstructions, look at the area where the coins are paid out from the hopper. Turn the hopper over as well as you testament find a natural spring loaded arm. When tokens are paid out that arm swings through a sensor, breaking the light as well as sending a signal to the machine that a token has been paid. Clean the sensor of all dust as well as dirt with a Q-tip as well as a little rubbing alcohol.

Step 6: Lubricate the Sensor Arm as well as natural spring

The natural spring loaded arm that breaks the sensor testament sometimes seize up because of dirt or rust. Spray a little silicone spray on the arm itself as well as the springs. Manually move the arm for a few minutes to work the lubricant into the arm as well as the natural spring. You testament feel it loosen as well as you testament feel the natural spring begin to pull the arm back when you pull it forward. When it moves freely as well as the natural spring pulls it back into place without hesitation you are done.

Step 7: Manually Test the Hopper

Put a few coins into the wheel as well as turn the wheel clockwise. You testament see the tokens fall into the holes in the wheel as well as move up toward the payout chute. If everything is cleaned as well as lubricated you testament see the tokens enter the payout chute one at a time as well as actually shoot out the hopper.

If the wheel is not moving easily clean it again as well as check for obstructions.

If the coins are entering the payout chute but dropping out as well as NOT BEING SHOT OUT then clean as well as lubricate the natural spring loaded arm, make sure the arm is springing quickly back into place after you move it through the sensor, make sure it is not hitting the sensor but moving THROUGH it as well as breaking the beam.

Replace the top of the hopper, install the hopper back into the machine, reset the machine using the reset key as well as test it.

[ad_2]